説明

• DC6-60V 400W BLDC Three-phase DC Brushless Motor Controller PWM Hall Motor Control Driver Board Motor Driver Module 12V 24V 48V Note: This driving force is a DC three-phase brushless management board requires a motor with Hall to work wisely This motive force is barely applicable to the electrical angle one hundred twenty degrees DC brushless with Hall motor Newly upgraded BLDC large voltage 6-60V excessive energy 400W DC three-phase brushless with Hall controller, help PLC 0-5V analog control help PWM management amplitude 2 External Signal Input Special Instructions: 1 From the motherboard P G 2 ports exterior PWM signal enter (the board comes with a potentiometer to the minimum, while shorting the board brief interface wiring see the diagram above) amplitude 2, frequency 50HZ-20KHZ 2 External analog 0-5V input, from the motherboard 2 terminals sub port input (the board comes with a potentiometer to the minimum, wiring see the above determine dashed line schematic) 3 External potentiometer speed control, from the motherboard 3 terminals sub port correspondingly linked (potentiometer on the board to the minimum, wiring see the above drawing potentiometer schematic) 4 forward and reverse and prevent by way of a change to ground (0 potential) low-level valid, is also exterior MCU to offer low-level signal Brake by way of a change to 5V high level legitimate The entrance row of terminals, are susceptible signals instantly into the MCU main control, can't contact and phone with high voltage solid current Interface Description: 1 MA MB MC section line output to the motor 2 5V GND main board with its personal 5V energy delivery (can be exterior power delivery recent would not exceed 50MA) 3 VCC GND main strength supply (external DC energy supply) 4 SC speed pulse signal output (only miss the interface, now not technical support) 5DIR route control ahead and reverse management interface (low-level positive exterior swap to ground) 6STOP stop Stop control interface (low-level legitimate exterior change to ground) 7BRAKE brake control brake control interface (high point legitimate for external switch to 5V) eight Speed control velocity signal input (on board integrated potentiometer pace management can also be exterior 0-5V analog PWM twin signal input velocity control) nine Ha Hb Hc +5V GND Hall signal power delivery input interface, generally with Hall motors have the corresponding 5 lines Chip activity upgraded performance secure with ahead and opposite stop brake function Debugging Instructions: please read and perceive earlier than powering on the examine machine, it's extremely important, very important, very important! After receiving the driving force board, first perceive whether or not the interface and your brushless motor interface can correspond on Brushless motor generally additionally has five Hall line or interface the place two is the Hall strength delivery line three is the Hall signal line to differentiate out particularly the Hall power supply line (Hall power delivery line commonly with purple and black line, there are not, no longer clear to find a manner to motor brands to) are not making a mistake 3 Hall sign line is generally marked with a b c, the motive force board additionally has ha Hb Hc 3 ports and other similar characters, respectively, equivalent to connect nice 2 The motor has three thicker section line drive board also has three section line interface, they are marked with MA MB MC characters and different identical characters, respectively, additionally correspond to connect well, to substantiate that the foremost energy delivery to work correctly (Such as the interface are properly comparable to the label, the flexibility cannot paintings properly, doesn't exclude the opportunity of brands don't standardize the label or different reasons, please persist with the three interface definition isn't always clean to debug) three If the motor part line and Hall line definition isn't clear, then the motor can be related to any of the three phase strains and pressure section line interface, while the Hall line of the 3 signal lines and power the board Hall interface any connection (but the 2 Hall power supply line must be able find and attach the right, remember!) Then within the first energy on, low voltage small current debugging (such because the situations with constant recent strength supply voltage to 7-12V current 1-2A), after which by way of arbitrarily swapping the order of the 3 Hall traces (motor 3 Hall sign line and force Hall interface between any two swap, every single switch strength test), till the power could be smoothly rotating operation at the right wiring, wiring has six combinations 1 ha hb hc 2 hc ha hb three hb hc ha 4 ha hc hb 5 hb ha hc 6 hc hb ha There are 6 combos of the above wiring methods, 1 is right, 2 and three motors could also be able to flip in one route The other three motors will not rotate 4 wrong wiring, do not excessive current, excessive voltage debugging, in any other case there is a threat of harm to the driver board, three Hall signal line change if the corresponding connected, power on the motor operating silky comfortable low-speed start comfortable torque; if the 3 Hall signal line series doesn't correspond to the correct connection, generally have the ensuing characteristics: 1 1 After strength at the motor can not normally start no response or start only shaking when now not ordinary rotation 2 There is a slight jitter delivery difficulties, and infrequently must be manually to turn up three The motor can turn in one direction, the other path cannot turn and some have a slight bath sound four motor birth jitter and powerless with a shower sound, the present is large, the ability tube of course heat critical Humanized design, the interface using the terminal block ordinary with warmth sink incorporated speed potentiometer on the board to the hands of the ability can be used to avoid wasting time and effort Specifications: Product name: 400W brushless Hall DC motor motive force Model: ZS-X11H V1 Operating voltage: 6-60V Maximum current: rated 16A height 20A Maximum power: 400W Overcurrent protection: Yes Product size: size 63MM*width 45MM*height 31MM Weight: about 77g Precautions: 1 The energy delivery circuit on the motherboard with out fuses, Jian Yi has added, the power supply tremendous and detrimental polarity will cause permanent harm to a few of the chips at the board (not even for about a seconds at excessive current) 2 In the conventional operation of the motor output with sampling overcurrent protection, due to the module power recent are very huge please don't paintings in the module is not standard artificial short circuit, yet a short circuit has burned the road burst tube may, the first wiring verify machine please use a small latest low voltage test, to be OK, after which through the excessive latest high voltage, due to bare board module on the market notice that the wiring cord insulation is precisely prohibited stable voltage touches the board parts three Do no longer connect the apparent and power the module voltage, current, power section would not event or far from the motor, to avoid inexplicable "nonsense" harm

• 
• 
• 
• 
• 

レビュー