Preces apraksts

• Due to Runcam Nano3 digital camera turned into discontinued, now the Mobula7 1s comes with Caddx ant digital camera since May 2024 The Mobula7 1s with Caddx ant camera we referred to as V2 version Please noticed New Mobula7 drone , this time the 75mm whoop in response to 1s power Thanks to the new AIO flight controller and the recent third-generation RS0802 brushless motor, the hot Mobula7 1s Will be the only option within the whoop season The world first 5-IN-1 AIO flight controller with ExpressLRS 2 , OPENVTX(up to 400mw), 12A Brushless Blheli_S ESC and Betaflight OSD popping out currently This is astounding flight controller for Brushless whoop You might get unbelievable RX and VTX range by using this flight controller The new RS0802 motors comes with a brand new unibell design, use 1 shaft and include PCB bottom plate, excessive performance and far more dependable New onboard OpenVTX , max strength as much as 400mw, provide RCE and PIT mode, it became very handy for race event Features: X12 5-IN-1 AIO flight controller built-in 2 ELRS V2 and Openvtx VTX Power as much as 400mw ELRS V2 Support NEW RS0802 KV20000 motors Runcam Nano3 The lightest 1/3 CMOS 800TVL Camera Smooth and powerful Compatible for 1S Lipo/LIHV Recommend 1S 450mah/550mah/650mah battery(Not include) Specifications: Brand Name: Happymodel Item Name: Mobula7 1S 75mm Micro FPV whoop drone Wheelbase: 75mm Size: 99mm*99mm*40mm Weight: 24g Receiver option: 2 ELRS SPI SPI Frsky D8/D16 now not like minded with EMAX E6 radio PNP (without onboard receiver) TBS version(with exterior TBS CRSF NANO RX) Package includes: Item Name Qty Mobula7 1S 75mm whoop Drone Frame (Mobula7 v4 frame) 1 Option1: X12 ELRS V1 flight controller integrated SPI ELRS 2 receiver 1 Option2: X12 Frsky V1 flight controller integrated SPI Frsky 2 receiver Option3: X12 PNP V1 flight controller with External TBS NANO receiver Option4: X12 PNP V1 flight controller without onboard receiver RS0802 KV20000 brushless motor 4 Gemfan 1610-2 bi-blade propellers(4cw+4ccw) 1 Runcam Nano3 1/3 CMOS 800TVL digital camera 1 Onboard 5 Openvtx 0mw~400mw VTX 1 1S parallel charging board 1 Propeller disassemble device 1 Extra camera cover 1 Spare components specifications: PNP Version (without onboard receiver) Full UART1 for external Receiver Support CRSF/GHOST/SBUS/IBUS/DSMX protocol IR1 pad(invert RX1) used for SBUS enter Motor Mode: RS0802 KV20000 Configu-ration:9N12P Stator Diamter:8mm Stator Length:2mm Shaft Diameter:Φ1 Motor Dimension(Dia*Len):Φ10*13 Weight(g):2 No Cells(Lipo):1S only Propellers Weight:0 Material:PC Pitch:1 inchProps Dia:40mm Center Thickness:5mm Center Hole Dia:1 Flight controller X12 ELRS V1 flight controller integrated ELRS 2 receiver Target: CRAZYBEEF4SX1280 X12 Frsky V1 flight controller integrated SPI Frsky 2 receiver Target: CRAZYBEEF4FR X12 PNP V1 flight controller with external TBS CRSF Nano receiver Target: CRAZYBEEF4DX X12 PNP V1 flight controller without onboard receiver Target: CRAZYBEEF4DX MCU:STM32F411CEU6 (100MHZ, 512K FLASH) Sensor: MPU6000 or ICM20689 or BMI270(SPI connection) Mount hole size: 25*25 Power supply: 1S battery input (DC 2) Built-in 12A(each) Blheli_S 4in1 ESC Built-in Betaflight OSD(SPI Control) Built-in 5 OpenVTX 0mw~400mw Built-in ExpressLRS 2,Frsky D8/D16 Built-in voltage detection Built-in current sensor Onboard 4in1 ESC Power supply: 1S LiPo/LiPo HV Current: 12A continual height 15A (3 seconds) Support BLHeliSuite programmable Factory firmware: Z_H_30_REV16_7 Default protocol: DSHOT300 Support Bluejay firmware When use Blujay firmware with 48khz, should set startup strength to 1100/1200 Onboard SPI ExpressLRS 2 Receiver Packet Rate option: 50Hz/150Hz/250Hz/500Hz ExpressLRS Firmware version: V2 RF Frequency: 2 Antenna : SMD antenna Telemetry output Power: <12dBm Receiver protocol: SPI ExpressLRS Compatible with ExpressLRS V2 TX Module Couldn&;t flash individually ExpressLRS firmware Onboard Frsky SPI D8/D16 receiver Version SPI BUS receiver Frsky D8 like minded Compatible Non EU transmitter D8 modelChannels: 8ch No floor interference ( Transmitter and receiver 1 m from the ground): 200meterFailsafe assist Onboard five OPENVTX Firmware version: OPENVTX Smartaudio v2 PIT Mode help RCE Mode assist Channels:48ch Transmitting Power: 0/RCE/25mw/100mw/400mw Power supply: DC 5V Current (5v):650ma~1000ma Runcam Nano3 Model: RunCam Nano 3 Image Sensor: 1/3″ CMOS Horizontal Resolution: 800TVL Lens : 2(M8) FOV 150° Signal System: NTSC S/N Ratio: >50dB Electronic Shutter Speed: Auto Auto Gain Control (AGC): Auto Min Illumination: 0@1 D-WDR: Auto Day/Night: Color Power:DC 3-5 Current: 110mA@5V 120mA@3 Housing Material: ABS Net Weight: 1 Dimensions: L14mm*W14mm*H9mm

• 
• 
• 
• 
• 

Atsauksmes