Preces apraksts

• Model No. : D4-P / D4-E 4 Channel Constant Voltage DMX512 RDM Decoder RDM/Numeric display/Seven PWM frequency/Linear or logarithmic dimming/Multiple defense Features: ● Comply with the DMX512 typical protocols. ● Digital numeric display, set DMX decode starting up handle via buttons. ● RDM operate can notice intercommunication between DMX master and decoder. For example, DMX decoder handle can be set through DMX draw close console. ● 1/2/4 DMX channel output selectable. ● 16bit (65536 levels) /8bit (256 levels) gray point selectable. ● PWM frequency 250/500/1000/2000/4000/8000/16000Hz selectable. ● Logarithmic or linear dimming curve selectable. ● Over-heat / Over-load / Short circuit protection, recuperate automatically. ● D4-P have Green terminal DMX sign ports, D4-E have RJ-45 DMX sign ports Technical Parameters: Input and Output Input voltage: 12-48VDC Input latest : 32 Output voltage : four x (12-48)VDC Output recent : 4×8A@12/24V 4×6A@36/48V Output energy : 4×96W @12V,4×192W@24V 4×216W@36V,4×288W@48V Output type:Constant voltage Note: 1. An DMX sign amplifier is required if greater than 32 decoders are connected, or use overlong signal line, sign amplification shouldn't be extra than five occasions continuously. 2. If the draw back affect occurs due to longer signal line or dangerous line quality, please try to join 0 90-120Ω terminal resistor on the end of every DMX sign line. Package content: 1pcs* D4-P / D4-E 4 Channel Constant Voltage DMX512 RDM Decoder 1pcs* Introduction Manual Operation System parameter ambiance ● Long press M and ◀ key in the similar time for 2s, practice for setup formula parameter: decode mode, grey level, output PWM frequence, output brightness curve, default output level, automatic clear screen. short press M key to change six item. ● Decode mode: brief press ◀ or ▶ key to switch 1/2/4 channel decode mode("d-1","d-2" or "d-4"). When set as 1 channel decode, the decoder occupy only one DMX address, and 4 channel output a matching brightness of this DMX address. ● Grey level: quick press ◀ or ▶ key to change 8bit("b08") or sixteen bit("b16"). choose sixteen bit if the DMX draw close assist 16 bit. ● Output PWM frequency: brief press ◀ or ▶ key to change 250Hz("F02"), 500Hz("F05"), 1000Hz("F10"), 2000Hz("F20"), 4000Hz("F40"), 8000Hz("F80") or 16000Hz("F16"). Higher PWM frequency, will set off lower output current, increased power noise, but more well matched for camera(No ickers for video). ● Output brightness curve: quick press ◀ or ▶ key to switch linear curve("C-L") or logarithmic curve("C-E"). ● Default output level: press ◀ or ▶ key to change default 0-100% point ("d00" to "dFF" ) when no DMX enter signal. ● Automatic clear screen: brief press ◀ or ▶ key to change enable ("bon") or disable("boF") automatic blank screen. ● Long press M key for 2s or timeout 10s, quit formulation parameter setting. DMX mode ● Short press M key, when display 001~512, enter DMX mode. ● Press ◀ or ▶ key to change DMX decode beginning address(001~512), prolonged press for fast adjustment. ● If there's a DMX signal input, will enter DMX mode automatically. ● DMX Dimming: Each D4-P/D4-E DMX decoder occupy four DMX deal with when connecting the DMX console. For example, the defaulted beginning take care of is 1, their corresponding relationship in the form:

• 
• 
• 
• 
• 

Atsauksmes