Açıklamalar

• DKC-1B single-axis stepper motor controller advantageous and adverse management velocity potentiometer double velocity PWM pulse generator Stepper Motor Controller DKC-1B The controller is an industrial kind stepper motor controller Adopt the hot common imported high-speed chip, and adopt the method of mixing utility and hardware to guarantee the strong anti-interference functionality of the controller At an identical time, it has reverse connection protection, overvoltage protection, and overcurrent protection to guarantee the safe operation of the controller in different harsh factory environments The controller is suitable for sensor-controlled round-trip movement control, fixed-length control, velocity control, and so on Product parameters: Ultra-wide voltage input: DC7-30V Multiple defense functions: opposite connection protection, overvoltage protection, overcurrent defense Speed legislation performance: with single/double pace speed legislation function; When single-speed pace legislation is used, the onboard pace law is attached externally, and the rate legislation is intelligently switched routinely Acceleration and deceleration: optimized S-shaped acceleration, with immediate stop/deceleration stop function Output frequency: The maximum output pulse frequency is 20KHz Input and output: All inputs are isolated through optocouplers, and the output is damaging pulse The input sign is lively low Delay function: The delay time of 0 is adjustable before the motor reverses VR1 potentiometer adjustment Back-to-origin function: The default is back-to-origin when the controller is powered on for the 1st time The pulse sign is 5V, the signal is valid on the falling edge, and the set off signal ought to be saved above 2 control function: 1 Immediate stop/deceleration give up operate Immediate stop: After receiving the stop or reversing signal, the motor directly stops or modifications course to realize exact control Deceleration stop: After receiving the give up or commutation signal, the motor begins to slow down to a undeniable velocity and then stops, realizing the sleek stop and commutation of the motor 2 Single/double speed control operate In the single-speed control mode, the onboard potentiometer and the external potentiometer are mechanically switched, and the exterior potentiometer interface is suspended, and the onboard potentiometer plays the position of velocity regulation If the exterior potentiometer (less than or equal to 10K) is connected, the control board will Automatically swap to external potentiometer for speed regulation; In the two-speed control mode, the two-speed control means that the motor rotates forward, and the reverse velocity is set separately The control standards of slow feed and instant return are discovered The ahead rotation is adjusted by way of an external potentiometer, and the reverse rotation is adjusted by means of the on-board electronic potentiometer 3 Back to beginning operate There is no desire for the operate of returning to the origin, and the beginning restrict could be immediately short-circuited with the common with a cord In computerized reciprocating mode, if you want to come to the origin, you should use a twine to instantly percentage the origin restrict and the unfavorable restrict brief circuit (effect: start is valid, the motor returns to the starting place within the unfavorable direction, and forestalls when it hits the damaging limit switch, which is the motion of returning to the origin, Press the start again, and reciprocate normally within the tremendous direction) Function Description: 1 Automatic round-trip mode: After the mode controller is induced to begin (touch the average terminal and the start input terminal), the motor will automatically circulation back and forth between the forward limit and the opposite restrict till the quit input is triggered After the motor reaches the forward rotation limit or the opposite rotation restrict and stops, there'll be a postpone of zero earlier than beginning to run, and the put off time is adjusted by VR1 The working velocity is regulated by means of VR2 or external pace regulation 2 Single set off mode: After this mode is induced and started, the motor will rotate ahead and the motor will give up when it hits the ahead limit If it is precipitated again, the motor will reverse, and when it hits the reverse limit, the motor will stop Trigger the starter motor back to copy the cycle 3 Single around day trip mode: After this mode is caused and started, the motor will run ahead and prevent when it hits the ahead restrict After a delay of 0, it's going to begin to reverse When it hits the opposite limit, the motor will quit four Jog mode: The beginning terminal is hooked up to the typical terminal for forward rotation, and it stops when it's released; the give up terminal is attached to the general public terminal for opposite rotation, and it's launched to stop; on this mode, the function of beginning again to the origin for the 1st time isn't out there Wiring and different directions 1 The controller is a universal stepping motor and servo motor controller The total stepper motor driver and servo motor driving force would be matched and used, regardless of the length of the motor Different motor motive force ports are marked differently, however the interface functions are an analogous EN=ENA=PREE allow PUL=PULS=CLK pulse DIR=CW=CCW course This controller uses the typical anode connection method: Controller +5V (OPTO) linked to motive force PUL+ and DIR+ controller Pulse- (PUL-) Connect to the heart beat input terminal of the driver (PUL-, PULS-, CLK-) Controller course - (DIR-) to drive path enter terminal (DIR-,CW-,CWW-) EN+, EN- This is usually left clean 1) We accept Alipay, West Union, TT All fundamental credit cards are authorized by way of secure charge processor ESCROW 2) Payment should be made inside 3 days of order 3) If you can&;t checkout instantly after public sale close, please anticipate a couple of minutes and retry Payments must be accomplished inside 3 days 1 You have 7 days to contact us and 30 days to come back it from the date components acquired If merchandise is on your possession is greater than 7 days, it's viewed used and refund or replacement usually are not approved And customer ought to be liable for all of the expenses of returning and reshipping 2 All return items must be in its fashioned conditions, including field and accessories Men made defects should not guaranteed, reminiscent of broken, scratched and so on, transport tracking number, specific reason for the return, and your po 1 Buyer&;s early confirmation could be extremely preferred after receiving the goods 2 Since your feedback is very fundamental to our business&;s development, we sincerely admire your superb feedback if you are satisfied with our product and repair 1 minute to you , extremely necessary importance to us three touch us earlier than leaving any detrimental or neutral feedback We will attempt our best to resolve any problems Thanks for your understanding! Welcome to our store--- UG International Supply Store Thank you for selecting UG We Will Be No In China! We are an honest vendor on Buydo As a producer of electronic module, UG have been in business more than 20 years, and therefor have vast experience in all of the line we manage To Be No Supplier Of Electronic Module In China! All our items from our manufacturing facility are with tremendous If you have any problems, we are very happy that you would be able to contact us We will attempt our greatest that will help you Hoping to establish an extended term cooperation with you Always Imitated, But Never Surpassed In China If Other Supplier Price Lower Than Us, Quality Than Us, Please Let Us Know, We Are Going To Beat Them! OEM Service Also Welcome!

• 
• 
• 
• 
• 

Gözden geçirmek