说明

• Food Waste Disposal ■ Snap design is easy to install, splash-proof and silent ■ No blade grinding + deep double layer shredding, safe and extra effective ■ Pure copper motor with German imported technology, stronger power ■ Overload defense + extreme temperature protection, longer existence ■ Daily use, a month of electrical energy consumption of about 2kWh, ultra-low calories intake Easy Disposal of Many Types of Food Waste ROUNY meals waste disposer can handle 95% of meals waste similar to culmination and vegetables, fruit peels and shells, small bones, small ribs, seafood fish bones, small shells, etc Cannot handle: plastic bags, hair, wide bones, huge shells and non-food waste One Click - So Easy Operation steps 1 Turn at the water tap 2 Start the processor with one button three Pour the meals waste into the grinding chamber 4*Please note: After expecting the food to be permanently ground, proceed to keep the faucet on and hold it on for 5 seconds and then flip it off five The machine is decided with overload protection device, exceeding a certain load or overheating, the machine will automatically close down Blade Free Grinding System The garbage disposer&;s grinding discs characteristic a bladeless grinding components with built-in 360° free-rotating knockout components Their form determines that the grinding discs are covered with enough knocking points throughout the machine&;s telling rotation, which can immediately split meals scraps immediately Efficient, Safe & Continuous Feeding The machine is designed with 3 layers of grinding expertise inside, the 1st layer is a stainless steel grinding disc that smoothly knocks up food residues The moment and third layers adopt tools structure, which is to deeply reduce the residue debris of the first grinding disc, to assure that 100 percent of the residue flowing into the sewer becomes fluid substance and 100% keep away from the issue of water pipe blockage Thickened Feed Silicone Cover Weaken the noise and prevent the residue from spattering when grinding Energy & Power Saving The leading machine adopts German permanent magnet motor, which provides powerful grinding strength and might be loaded with 1000ml at a time Users within the case of on daily basis use of the machine, 1 month solely devour about 2kWH of electricity Perfectly achieve low energy consumption, save time and energy, and more safety! Suitable Size 1 The product is acceptable for 110mm sink opening 2 The product comes with air switch as standard, and the recommended installation hole is 28~30mm 3 It is recommended that the bottom thickness of the installable sink be within 10mm Easy to Assemble This product has a screw design that may be put in individually through one grownup Please confer with the guide and product video for installation, which will provide comfort in your installation Product Q & A Q: How can I install the mechanical device if the sink diameter is not 11cm? A: The machine is acceptable for sink diameter of 11cm, if the sink diameter isn't suitable, we recommend you should use reducer (reducer ring) to change the sink diameter Q: How massive is the outlet of the air switch? A: It is usually recommended that the diameter of the hole within the counter peak or wall is 2~3cm Q: Is the mechanical device smooth to install? A: It is really easy to install, installation requires some power We simulate the installation steps in the product video, at the moment greater than 99% of shoppers can understand the set up steps in the course of the video and instructions, while you discover it very difficult, it is suggested to invite a professional for installation Q: Is the stone sink compatible for putting in the machine? A: It is usually recommended to judge through the thickness of the sink bottom, if the lowest thickness is 10mm (1cm) or less, it's possible to put in the machine It is recommended to polish the stone sink mouth mushy earlier than putting in the machine Q: How can I check if the machine is operating correctly once I get hold of it? A: Please install the air change of the machine, then plug within the strength and press the button, the mechanical device can start or shut down normally Q: I acquired a new machine and located that there are scratches contained in the grinding disc, how can I do? A: The product is inspected at the factory, powered on and the mechanical device is began Therefore, the grinding disc left operating traces, this can be a standard situation, buyers can install and use the machine normally, please do not worry Q: What must I do if the mechanical device is stuck? A: A jammed state means that the machine has activated the electrical defense operate Please bring to an end the power and clear all the residues and foreign objects within the grinding chamber (especially the sting gap), insert and turn the grinding disc with a screwdriver, and at last press the purple reset swap frivolously and power on to switch on usually

• 
• 
• 
• 
• 

审核