Beschreibung

• DC5-12V LED Controller 2048Pixels For WS2801 WS2811 WS2812B 2048 LED Strip Light Description: 1. Built in 102 patterns (without SD card), management could be geared up with SD (<8G) 2. When starting up, there's no SD to automatically call the inner pattern, and putting SD will mechanically name the SD card pattern. RJ-FSD-1000B would be sent as DMX512 and TTL signals. In the SD card state, the ancient DMX512 can be utilized to make a decision included patterns and speeds. 4. Multiple devices would be synchronized, and the synchronization sign is recommended not to exceed 50 meters. The actual size is 2 hundred meters. 5. Maximum strain 2048 pixels. The maximum refresh payment is 30 frames (<512 pixels). 6. The most distance TTL between the controller and the lamp is<15 meters; 485 signal<30 meters. TTL can connect about 10 items simultaneously. Product parameters: Working calories supply: DC5-12V Power: 3W Size: L122mm * W 73mm * H25mm 2、 Supporting IC: Specific model: TM: TM1803, TM1804, TM1913, TM1809, TM1812, TM1914, TM1829 UCS: UCS2903, UCS2909, UCS2912, UCS1903, UCS1909, UCS1912 WS: WS2801, WS2812, WS2811 INK1003: INK1003 LPD: LDP6803, LDP8806, LDP1109 D705: D705 SM: SM16716, SM1672616703, DMX512 APA102: APA102 DMX512: DMX512 P9813: P9803 SK6812: RGB whole color three channel, RGBW four channel 3、 Automatically distinguish SD cards or inside patterns Automatically determine whether there is a card when starting up up, name SD pattern if there is a card, and robotically call inside sample if there isn't any card. 4、 Set the pattern and speed. 1. In the SD card state, you might favor patterns and speeds via means of urgent the buttons, and the [on/off] key adjusts the brightness. Other operations are similar to when there is no card, see details below. 2. Press the second one button of [mode/speed] to cycle in the course of the exhibit of S001 and P001, where S represents the rate and P represents the sample (Figure 1). At this time, it's essential to expand or decrease the rate by utilizing [UP] and [DOWN]. 3. Long press and keep the second one key [MODE/SPEED] to reveal A000, the place A represents the DMX512 address. Note that the DMX512 handle is just useful for DMX512 interpreting and when utilizing a standard DMX512 console to administer incorporated patterns. Use the UP and DOWN keys to increase and decrease. 5、 Wiring formula TTL: Single line and dual line sign interface. DAT: Data CLK: Clock GND: Signal floor DMX512: When choosing a model DMX512, ship a DMX512 signal, and when sending a differential signal for other models; Cooperate with the 485 receiving board to transmit alerts further. D+: DMX512 signal A, D - DMX512 sign B, GND: No wiring is required below steady conditions. 6、 Operating directions for within patterns Firstly, press the [ON/OFF] key and the demonstrate exhibits OFF to enter the programming state (Figure 1) Then press [Mode/Speed] to choose (Figure 2), choose the model, and then press the [On/off] button to exit. Control level setting: First, press the [ON/OFF] key to reveal OFF on the display screen and enter the programming state. Then, set the variety of facets with [UP] and [DOWN]. Press the [On/off] key to exit. 7、 DMX512 console 1. DMX512 management console, controlling the interior or SD patterns of RJ-FSD-1000B, a number of instruments are used synchronously, and the 1st one is used for wiring. Precautions: 1. Please pay attention in on rain protection throughout installation. The recommended normal operating voltage is DC5-24V Function 1: Calling internal and exterior patterns RJ-FSD-1000B (large card): Automatic discrimination, card insertion automatically calls SD, no card automatically adjusts inner patterns. Function 2: Synchronize under SD card repute RJ-FSD-1000B (large card) automatic discrimination, as prolonged as there isn't any controller in front, this technique defaults to being the biggest control and sends a synchronization signal downwards. Function 3: Function SD broad card, the massive card holder is imported, self-locking, and won't loosen. When pulling out the card, it's best to press the self-locking button to take away it. Package include: 1pcs x LED Controller

• 
• 
• 
• 
• 

Rückmeldung