Description

• Features: 1 fine material, long carrier life, high-quality circuit, stable functionality and high efficiency 2 Reverse connection protection: with opposite connection protection, even though the wires are related in reverse, they will not be broken 3 With fan control: Intelligent fan management (the fan can automatically and infinitely variable velocity per the temperature of the radiator) 4 Protection functions: overheating defense "otP", prompt over strength defense "oPP", over voltage defense "ouP", opposite connection protection, abnormal strength delivery voltage defense five Wide range of applications: can measure the particular capacity of the battery, examine the particular energy of the weight and other applications 6 Increase the support for four-wire test in digital load mode, with self sufficient four-wire voltage indicator Parameter: Working power supply: DC12V regulated (11-13V) now not less than 0, energy supply isn't always suitable will exhibit Err6 Interface: 5*2 around mouth inside the advantageous pole Operating mode: single mode constant current (CC) Discharge current: zero in steps of zero or 0 Discharge latest error: 0% plus or minus 0 Capacity verify error doesn't exceed: zero 2%, 2A 1%, 5A and above 1% Lower restrict (termination) voltage setting range: 0 in steps of 1V or zero Discharge voltage: zero (affected by way of MOS inner resistance and other losses, the measured enter 1V can help up to 6-7A current, nine need to be measured voltage more than 1) Voltage dimension error would not exceed: 0% ± 0 Power: 112W over power computerized latest limit (for example, for 110W can open nine at 11V and solely five at 20V) Power: 62W over power automated current limiting (e for 60W it can be 9 at 6V but solely three at 20V) Battery examine statistics limit: 999 or 9999Wh, attain the value to stop the test (the first to reach the worth because the give up condition) Product size: 110W: 122mm*70mm*77mm (fan protrudes about 22mm from the board) 60W: 106*70mm*57 (fan protrudes from the board about 12mm) Positioning hole position: 60mm * 88mm gap diameter three installed 5mm submit (60W for copper post 110W for insulated nylon post) Package include: Tester*1 Accessory kit *1 Operating instructions: I Function mode surroundings (default factory electronic load mode): Press and hold "ON/OFF" at the identical time to the tester energized till the show Fun * and then launch the button, at this time into the operate surroundings menu By rotating the knob to change the setting, through pressing "ON/OFF" to switch to the next step, set within the following order: 1 Mode surroundings "Fun1" is electronic load mode, "Fun2" is battery skill examine mode 2 Buzzer switch environment "bEon" buzzer on, "bEoF" buzzer off three Display brightness surroundings "Lt-1" "Lt-2" "Lt-3", three brightness levels could be chosen Finish this back press "ON/OFF" to avoid wasting and exit the setting After that, the tester will restart and input into typical operating condition Second, the digital load mode: 1 Turn on the 12V power supply, make sure it is in the give up state ("RUN" lamp does not mild up, in any other case press the "ON/OFF" off) beneath the connection of the ability delivery below verify to the power enter port (P + P-), resembling the use of four-wire connection, please also connect the voltage detection line to the (V + V-) socket If using four-wire connection method, please connect the voltage detection line to the (V+V-) socket on the identical time If the measured energy delivery voltage is higher than 1V, the voltage might be displayed automatically, and the "L-4" lamp will light up when it is recognized as 4-wire mode Note: Do not contact the radiator with the screwdriver when wiring, and don't join the destructive pole anyway 2 Set the present and the decrease restrict voltage through the knob, rotate the knob to set the price of the present environment position, press the knob to change the environment digit, the variety of the current surroundings role will blink, greater than 3 seconds of inactivity will routinely exit the setup back to the normal show of voltage and recent three Press "ON/OFF", the burden starts to run, "RUN" lighting up, the circuit applies the set discharge recent to the enter strength supply beneath test, and at the same time, the particular enter load voltage is displayed on the higher line, when the voltage is less than the set lower limit voltage, "RUN" light flashes and accompanied by a quick buzzer alarm When the voltage falls under the set decrease restrict voltage, "RUN" mild flashes and accompanied by means of a short buzzer alarm four The current would be changed at any time during the test, if the lower restrict voltage ought to be modified, the weight must be grew to become off earlier than amendment Note: When in alarm state, the present can only be adjusted down, no longer up! Tester computerized power-down save operate can save the set parameters and working status, when the power failure to resend energy could be restored before the power failure of the whole state and data Third, the battery skill examine mode: 1 The battery beneath examine should be totally charged with a special charger first! 2 Power on the tester to go into the battery skill verify mode, connect the superb and adverse battery recent strains to the P+P- terminals, while you use the four-wire fixture test, please join the four-wire fixture voltage examine interface high-quality and destructive to the V+V- port The tester will demonstrate the battery voltage, if the 4-wire voltage check line is hooked up correctly, the "L-4" lamp will remove darkness from on the same time three Set the release current and discharge termination voltage by means of rotating the knob (please seek advice from the description of II:2), after setting, press "ON/OFF", the tester will first and foremost come across the battery and the line, and then input into the test, if there is a fault code, please check with the again of the description 4 During the checking out process, the upstream digital tube will demonstrate the battery voltage, latest discharge means Ah and current discharge calories Wh When the release is done (battery voltage is less than the set voltage), the tester will exhibit the data in Ah and flash rapidly, accompanied by a buzzer alarm sound 5 Press the knob or start/stop change to stop the alarm, you possibly can rotate the knob to view the battery discharge information adding discharge capability Ah, discharge calories Wh and platform voltage V Press "ON/OFF" again to clear the data and restore to the initial setup interface before trying out the next battery Supplementary notes: 1 You can modify the discharge current at any time during the battery test, if you want to readjust the termination voltage, you can pause the release amendment via clicking "ON/OFF" (the pause discharge will go back to the atmosphere page, the discharged records aren't lost, at this time, long-press "ON/OFF" can clear the data) (the discharged information aren't lost, then lengthy press "ON/OFF" to clear the data) 2 Tester power down routinely save the power to record the set parameters, and in the test activity and the end of the verify alarm state happens when the power failure to checklist all the parameters and the state of the re-powered all mechanically restored Fault protection code and meaning: Err1: ability verify battery voltage is simply too high Err2: Battery voltage is lower than the set termination voltage, not linked to the battery or opposite battery Err3: The inside resistance of the road is simply too wide or the battery cannot withstand the set discharge current Err4: Circuit failure Po-L: Power delivery voltage is just too low or insufficient energy Po-H: Power supply voltage too excessive otP: Overheat defense Ert: Temperature probe failure or too low temperature ouP: Voltage too high in digital load mode

• 
• 
• 
• 
• 

Review