Description

• IR-1 FEATURES Includes 4 250 cm (98") cables with hooked up magnets and unique fittings: Barbed adaptor - Threads into the end of brake & shift cable housing in addition hydraulic brake hose Rubber adaptor - Securely holds digital moving wire reminiscent of and Campagnolo® EPS -specific adaptor - Specially-designed connector clips into the end of the shift cable, and is completely sized to fit into body holes as small as 6 mm Reverse-polarity magnet - Used in conjunction with any of the alternative handbook cables - feeds into the opposite finish and meets the leading cable in the middle, assisting in routing on frames with difficult interior shapes CCP-22 FEATURES Compatible with methods that use an M8 or M10 threaded crank bolt, including: Square taper BNI cranks for e-bike techniques NOTE: For crank techniques that use an M12 or M14 crank bolt, reminiscent of ISIS Drive or , use the Park Tool CCP-44 or CWP-7 CCP-44 FEATURES Compatible with systems that use an M12 or M15 threaded crank bolt, including: ISIS Drive ISIS Overdrive systems NOTE: For crank systems that use an M8 or M10 crank bolt, reminiscent of sq. taper or , use the Park Tool CCP-22 or CWP-7 CWP-7 FEATURES SMALL SWIVEL FOOT Fits crank arms with M22 x 1 threads Compatible with programs that use an M8 x 1 threaded crank bolt, including: Square taper BNI cranks for e-bike programs LARGE SWIVEL FOOT Fits crank arms with M22 x 1 threads Compatible with methods that use an M12 x 1 or M15 x 1 threaded crank bolt, including: ISIS Drive ISIS Overdrive programs CC-3 FEATURES 5-to-10-speed chains: replace chain at or simply before 0% 11-to-12-speed chains*: update at or simply before 0% Check with producer for specific replacement directions *Use the CC-4 for Flattop™ and T-Type 12-speed chains BBT-9 FEATURES Fits 16-notch software fittings with a major diameter (outside of notches) of 44–45 mm and a minor diameter (inside of notches) of 42 mm, including: BB80, BB5700, BB70, BB51, and former exterior bearing threaded cups Threaded bottom bracket cups from/ 16-notch disc brake rotor lockrings 16-notch BBSH, BBS02 mid-drive motor lockrings Fits 8-point software fittings on crank arm caps: Equivalent to TL-FC16 or TL-FC18 tool PRESS The DT-2 Rotor Truing Fork quickly became one in all my favorites It&;s an easy bar stock, with two assorted slots offering distinct leverage ratios to true rotors, which means I don&;t have to do it barehanded with my thumbs opposed to palms for leverage That system works, however the DT-2 retains oil off the rotors and permits a chunk extra fine-tuning than the aforementioned digital manipulation PS-1 FEATURES • Thickness: 1 mm (0") • Length: 162 mm (6") CC-4 FEATURES 5-to-10-speed chains: replace chain at or just earlier than 0% 11-to-12-speed chains: update at or simply earlier than 0% Check with manufacturer for particular alternative instructions PW-5 FEATURES Length: 11" (290 mm) Weight: 256 g (9 oz) The FR-5 is designed to slot the commonest device becoming found on 7-to-12 pace cassette lockrings, including units made by means of and others Also matches disc brake lockrings and lockring adapters with 12 inner splines, and height caps of a few Rock suspension fork items Thin wall structure permits use without removing of cones and locknuts The 1" hexagonal base can be utilized in conjunction with a socket, wrench, or bench vise Heat-treated alloy device metal structure for a lifetime of use FR-5 FEATURES Fits 12-spline instrument fittings with an approximate outer diameter of 23 mm including: Cassette lockrings fromand others Disc brake lockrings and lockring adapters with 12 inside splines fromand other manufacturers Top cap of some Rock suspension fork models including Center bore for axle clearance is 12 mm The reliable design of our FR-5 lockring software with an added 12 mm instruction manual pin to stabilize the instrument when used with via axle hubs The FR-5 is designed to slot the commonest device becoming stumbled on on 7-to-12 speed cassette lockrings, adding units made through , and others Also fits disc brake lockrings and lockring adapters with 12 inner splines Thin wall structure permits use with out removing of cones and locknuts The 1" hexagonal base can be used in conjunction with a socket, wrench, or bench vise Heat-treated alloy instrument steel structure for a lifetime of use FR-5 FEATURES Fits 12-spline tool fittings with an approximate outer diameter of 23 mm including: Cassette lockrings from Disc brake lockrings and lockring adapters with 12 inside splines from and different brands When removing and putting in bicycle components, having the proper tools is important The Park Tool BBT-5/FR-11 is designed to fit the tool fittings discovered on Campagnolo® cassette lockrings and cartridge bottom brackets Constructed from heat-treated alloy instrument steel, the BBT-5/FR-11 incorporates a 1" software becoming for use with an adjustable wrench, socket, or bench vise BBT-5/FR-11 FEATURES Fits 12 spline/approx 22 mm OD software fittings Fits all cassette lockrings Also matches cartridge backside brackets adding ® Base length for socket or wrench is 1" (25 mm) NOTE: The BBT-5/FR-11 isn't always interchangeable with the FR-1, FR-5, or FR-7 Each software fitting has its personal exotic instrument profile The FR-4 is designed to slot the 20-spline tool fittings chanced on on older SunTour® freewheels Constructed from heat handled alloy tool steel, the FR-4 includes a 1" instrument fitting to be used with an adjustable wrench, socket, or bench vise FR-4 FEATURES Fits 20-spline instrument fittings with an approximate outer diameter of 21 mm The FR-7 is designed to slot the 12-notch tool fittings chanced on on freewheels Constructed from heat-treated alloy instrument steel, the FR-7 incorporates a 1" device fitting for use with an adjustable wrench, socket, or bench vise FR-7 FEATURES Fits 12-spline/23 mm OD tool fittings Center bore for axle clearance is 10 mm NOTE: The shape of the FR-7 seems to be corresponding to the FR-1 (f, and similar freewheels) The FR-7, however, is made with a marginally larger outdoors diameter (23mm) to fit the Freewheel To make it easy to distinguish between the 2 removers, the FR-7 has a silver-colored plating The slightly smaller diameter FR-1 is black The FR-1 is designed to slot the most common instrument fitting stumbled on on 5-to-10 pace bicycle freewheel systems, including many models made via and DNP Epoch™ Features an enlarged thru-hole to accommodate 14mm strong axles The 1" hexagonal base can be used in conjunction with a 1" socket or adjustable wrench Heat-treated alloy software metallic construction for a life of use FR-1 FEATURES Fits 12-spline tool fittings with an approximate outer diameter of twenty-two mm Center bore for axle clearance is 15 mm NOTE: For freewheels, use the FR-7

• 
• 
• 
• 
• 

Review