Description

• RC Parts & Accs : Speed Controllers Material : Composite Material Brand Name : DarwinFPV Origin : Mainland China Recommend Age : 14+y Use : Vehicles & Remote Control Toys The customary design intention of the ;cement; ultra-durable series of products: How to make fpv drone break throughout the environmental limits again? To boost the joys of flying for pilots, ride varied flying perspectives, shoot different materials, and not be fearful of dust, rain, snow and any harsh environment We have observed that in order to prevent dust, tin slag, grass juice, rain, etc from destructive digital equipment, the pilots have attempted methods resembling anti-corrosion paint and published elements to guard the kit Warranty policy, and occasional reliability, excessive chance of failure To this end, Darwin released a brand new ;cement; ultra-durable series, so you have more self belief to venture the acute surroundings ;If you're afraid that the drone will fall because of accidents, please use cement!; Spoiler: Why is it referred to as ;cement;? Because its appearance is potted like cement, and it has a similar solid sturdiness as cement In short, ;If you are petrified of falling because of an accident, use cement!; Darwin FPV ;cement; ultra-durable F7-100A waterproof stack is the tip stack launched via the Darwin team for pro pilots It completely solves the industry situation of poor reliability of fpv drones, allowing you to fly in any environment and greatly recovering the fun of flying Satisfy your varied artistic inspirations! We have announced many novel aspects in this stack, equivalent to canceling all the easy-to-loose direct socket interfaces, canceling the traditional heat dissipation shell with low thermal conductivity, including water-resistant and impact-resistant medicine with glue filling, and adopting the ultra-high latest MOS bus technology has added more than 10 core hardware protections, akin to delicate delivery defense circuit, anti-reverse connection, anti-short circuit and anti-overcurrent circuit, to ensure steadiness and reliability in severe environments And maintain the product length and weight practically the same as normal stack, without affecting your installation compatibility and flying really feel Specifications: FC : MCU: STM32F22 Gyroscope: MPU6000/ICM42688 OSD: AT7456E Black box: Built-in 8G SD card BEC output: 10V/3A 5V/3A Reserved interface: 5x Uarts(1,2,3,4,6), 4x Softserial, 1x I2C, 4x RGB, 1x Buzzer, 1x USER(C09) Input voltage: 2-6S Lipo Firmware name: DARWINF722HDV2 Mounting hole: 30 x 30 Dimensions: 39 x 39 x 4mm Weight: 10±0 ESC: MCU: 32-bit F4 120MHz main frequency, most support 128KHz PWM Packet Rate Continuous / height current: 100Ax4/120Ax4 (continuous 100A calls for water cooling environment) Input voltage: 3-6S Lipo Support throttle signal: Dshot150/300/600/1200 MultiShot Oneshot42 Oneshot125 Current sensor: help (current meter scale: 125) Firmware name: DARWIN_F4_60 Power cord: 14AWG-120mm lengthy (the ESC terminal and electrolytic capacitor had been welded at the factory) Power plug: XT60 Dimensions: 36 x forty two x 7 Mounting hole: 30 x 30 Weight: 23±0 (excluding capacitors and tool cords) Apply for: 5-10 inch FPV Drones Packing list: FC: 1 x DarwinFPV ;Cement; Ultra Durable F7 Waterproof Flight Controller 1 x 30mm ESC cable (8P) 1 x 65mm analog VTX cable (4P) 1 x 65mm GPS cable (6P) 1 x 65mm receiver cable (4P) 1 x 65mm HD VTX cable (6P) four x M3*4 shock-absorbing balls (installed on FC) 1 x sticky label ESC: 1 x DarwinFPV ;Cement; Ultra Durable 100A Waterproof ESC 1 x 30mm ESC cable (8P) 1 x XT60 1 x 14AWMG strength cable with a size of 120mm (soldered to the ESC) 1 x 35V/1000uF electrolytic capacitor (soldered to the ESC) 4 x M3*6 shock-absorbing balls (installed on the ESC) 1 x sticky label Stack: 1 x DarwinFPV ;Cement; Ultra Durable F7-100A Waterproof Stack 1 x 30mm ESC cable (8P) 1 x 65mm analog VTX cable (4P) 1 x 65mm GPS cable (6P) 1 x 65mm receiver cable (4P) 1 x 65mm HD VTX cable (6P) 1 x XT60 1 x 14AWMG strength cable (length 120mm, soldered to the ESC) 1 x 35V/1000uF electrolytic capacitor (soldered to the ESC) 4 x M3*4 shock-absorbing balls (installed on FC) 4 x M3*6 shock-absorbing balls (installed on the ESC) 4 x M3*25 hexagon socket head black 304 screws (installed at the stack) 4 x M3 nylon nuts 1 x sticker

• 
• 
• 
• 
• 

Review