Description

• Product Name: 5V 9V 12V 24V DC/AC Motor Controller Relay Board Forward Reverse Control Automatic Timing Delay Cycle Limit Start Stop Switch Package inlcuded: 1 PCS Multifunction AC/DC motor Reversible controller Description: 1 Dual strength delivery (two energy materials can't be powered on the same time): Power supply 1, DC 6; Power delivery 2, DC 5V 2 Working current: (Normal Mode) standby current 41mA, operating current 82mA; (Energy-Saving mode) Standby latest 7mA, working latest 44mA three There are three input management ports: ahead control(FWD), opposite control(REV), and forestall control(STOP) four Two enter trigger modes, Low-Pulse trigger mode, Low-Level trigger mode five Delay time: 0 seconds, 1-9999 seconds, 1-9999 minutes 6 Cycle times: no cycle, 2-99 cycles, consistently cycle 7 Three indicators: forward indicator(F LED), opposite indicator(R LED), give up indicator(S LED) 7 6 functional modes 8 Relay load current, commended less than 5A 7 Size: 80*50*19mm8 Weight: about 50 grams This is a multi-function DC/AC motor forward and reverse controller with multiple control modes Many management purposes can be derived via life like settings Port: DC five female : Power supply 1, DC 5V strength supply : Power 2 positive, DC 6 strength supplyGND : Power supply 2 negativeFWD : Forward input management (partial Function-Mode is invalid)REV : Reverse input management (partial Function-Mode is invalid)STOP : Stop enter control (partial Function-Mode is invalid)M+ : Motor advantageous M- : Motor negativeP+ : Positive motor power supplyP- : Negative motor power supply Wiring: 1 The operating energy supply is 6 The motor is a DC 1-110V DC motor or AC 85-265V AC motor The working energy delivery is 5VDC The motor is a DC 1-110V DC motor or an AC 85-265V AC motor How to use: Q&A: Q1: Why is the digital tube now not lit after power-on? A1: This is because the “Energy-Saving mode” is set, please press and maintain the OK button for 5 seconds to exit the energy saving mode Q2: Why does the motor no longer work after the motor is hooked up to the M+/M- port? A2: The working strength and motor power of the board are autonomous You should delivery strength to the motor The energy port is P+/P- port It is usually recommended to use two separate energy supplies for the operating strength supply and the motor strength delivery Q3: Why is the parameter surroundings invalid? A3: After atmosphere the parameters, ensure you re-power,Parameter settings could be kept completely Trigger mode: 1 low pulse set off (falling edge trigger) 2 low level trigger (rising edge trigger) Timer: T1: Forward timer T2: Reverse timer T3: Stop timer Time unit : zero second, 1 second, 1 minute Relay action: Motor ahead : Relay 1 is ON, relay 2 is OFF, and the F LED indicator is flashing Motor opposite : Relay 1 is OFF, relay 2 is ON, and the R LED indicator is flashing Motor stop : Relay 1 is OFF, relay 2 is OFF, and the S LED indicator is flashing Factory settings: Press the "++" and "--" buttons concurrently for 5 seconds Energy-saving mode: Press and maintain the “OK” button for five seconds to enter the “Energy-saving mode” Press and maintain the “OK” button again for 5 seconds to exit the “Energy-saving mode” Energy saving mode simply turns off the digital tube and LED indicator, and other applications are ordinary Function mode: F-01 After power-on, the motor is ahead T1 time; then the motor stops T3 time; then the motor reverse T2 time; so it is repeated Nx occasions When the STOP port is triggered, the motor stops operating immediately (FWD, REV port is invalid) F-02 This operate is a F-01 variant F-01 is administered instantly after power-on, but F-02 needs to set off FWD or REV port to run F-11(Trigger reversible 1） Trigger the FWD port, the motor is ahead T1 time, and automatically stops (in order to protect the motor, during the delay period, trigger the REV port to stop T3 time after which reverse T2 time, trigger FWD port to re-time T1) Trigger the REV port, the motor is reverse T2 time, and routinely stops (in order to protect the motor, during the delay period, the FWD port is brought on to stop the T3 time after which the T1 time is forward, and the REV port is re-timed T2) When the STOP port is triggered, the motor stops immediately, despite whether or not the motor is forward or reverse F-12(Trigger reversible 2） Trigger the FWD port, the motor is forward T1 time and forestalls routinely (during the put off period, aside from triggering STOP port, the opposite ports are invalid) Trigger the REV port, the motor is reverses T2 time, and mechanically stops (during the put off period, aside from triggering STOP port, the opposite ports are invalid) When the STOP port is trigger, the motor stops immediately, despite whether or not the motor is ahead or opposite F-21 When the FWD port is low level, the motor is forward, and after the FWD port is released, the motor stops When the REV port is low level, the motor is reversed, and after the REV port is released, the motor stops In this mode, the FWD and REV ports can't be related low point on the similar time, and the STOP port is invalid F-22 When the FWD port is low level, the motor is forward, and after the FWD port is released, the motor stops When the REV port is low level, the motor is reversed, and after the REV port is released, the motor stops In this mode, the FWD and REV ports cannot be connected low point on the identical time, triggering the STOP port, the motor stops straight Parameter setting: There are 3 menus: Work Menu, Function Menu, Parameter Menu Note: When coming into the “Function Menu” or “Parameter Menu”, the module still works normally (countdown and the trigger is working normally) The set parameters are legitimate solely after being powered on back 1 Power on to input the operating state (Work Menu) If the present operate is F-01, then the motor direct run and the digital tube reveals the countdown F-01 is displayed after the operation is done If the present operate is different functions, equivalent to F-11 Then the electronic tube reveals F-11 After the trigger, the electronic tube displays the countdown After the operation is completed, F-11 is displayed Description: The ahead countdown F LED indicator flashes, the opposite countdown R LED indicator flashes, and the S LED indicator flashes when stopped 2 In the working state(Work Menu), short press the SET button to enter the “Function Menu” (Above table) three Press the "SET" button beneath “Function Menu” to go into the “Parameter Menu”(Above table) In the “Parameter Menu”, short press the "SET" button to select the parameters of 1-9, and set the parameters in the course of the "++" button and the "--" button Short press the "OK" button to avoid wasting the current settings and go back to the previous menu (Function Menu) Description: 1 Timer T1 T2 T3 time unit is zero sec / sec / min, so the timing range of T1 T2 T3 is 0 seconds, 1-9999 seconds, 1-9999 minutes 2 The variety of cycles is the variety of repeated actions (Nx =0 means always loop, Nx =1 ability no loop) So you possibly can set the variety of loops: 1-99 times or for all time loops three F-21, F-22 function, Nx=1 parameter cannot be replaced

• 
• 
• 
• 
• 

Review