DC 12V PWM Temperature Controller Fan Speed governor four Wire Speed Controller Switch for PC Fan Alarm STK IC The controller solely controls the rate of the 4 line usual specification Intel PWM fan, don't flip off the fan With full digital control, accurate temperature atmosphere and precise control It integrates guide velocity law and automated temperature control and speed law operate Manual velocity management from 10%-100%, every single 5% is a gear Automatic temperature management speed from 30 degrees Celsius, there are forty nine styles of temperature zone combination It helps three line to 4 line control, surroundings parameters routinely save Parameter Value Operating voltage DC12V can paintings in 8-18V range Fan interface 2510-4P lacks 1 bends (special interface for laptop 4P fan Consumption current No greater than 20mA Fan latest Less than 3A Drive output range 10% -100 Operating temperature -10 Celsius to 60 Celsius Temperature probe parameters NTC 50K B=3950 Probe temperature Small black head 120 levels Ring probe one hundred ten Celsius Board length 34mm*19mm*11mm (excluding prolonged interface) Fan interface extends 8mm Setting parameters default manufacturing facility Low pace 20% Acceleration temperature 30 Celsius Acceleration width 5 Celsius Do not close down the output At this temperature setting, preserving the probe with the palm of the hand will accelerate in a couple of minutes If the probe is clamped into the armpit, it will attain full velocity in 2 mins three Components: 1> Input line: red black power line is barely welding 12V positive and damaging strength cord, as a general use The 3 wire connector is provided with a 2510-3P plug, which is used to measure the rate of some leading board three cord fan ports Large 4P interface facilitates energy acquisition from chassis 2> temperature probe: small black line&;s head is short, low warmth capacity It is acceptable for trying out slim space and air temperature, and the reaction is comparatively instant The ring probe is enclosed inside a ring steel head with a diameter of 4 It is suitable for mounting on the radiator or other heating object surface with screws four Manual automated integration control: 3 parameters are adjusted: birth speed po, delivery temperature expand Tu revolutions and Delta TD temperature when the revolutions attain the utmost Po is determined after switching on Double click on down, single up 1 + 2 burns attain a minimum, 2 + three maximum revolutions To configure Tu preserve three seconds, birth flashing slowly Also click on and put the worth at the desk Keep one other three seconds, beginning flashing fast, customize TD 1> Manual control without temperature probe Click / double-click (double-click pace not too fast) button up / down equipment Each shift continues after 20 seconds, and the gear is routinely stored The No 2 indicator flashes rapidly in 20 seconds (when the temperature management is invalid) When the flash is stopped, it signifies that the dossier has been stored The 3 / 1 indicator gentle is always on once you can't proceed to increase / now not proceed to minimize the placement 2> When the temperature probe is installed, the guide speed is used as the preliminary low speed (bottom line speed) When the temperature exceeds the accelerating temperature, the fan velocity speeds up easily with the rise of temperature the temperature reaches and exceeds the sum of the acceleration temperature and the acceleration width (full speed temperature), the fan runs at complete speed the acceleration temperature and acceleration width parameters as proven within the schematic diagram beneath The quantity 123 represents the indicator light on the board (red) and the (white) state is displayed in binary order: 5 instruction: Bottom line 20%, acceleration temperature 35, acceleration width 15 the probe temperature is lower than 35 levels centigrade, the output signal is often 20% When the probe temperature is increased than 35 degrees, the controller can develop theoutput signal easily in keeping with the temperature rise, and the fan accelerates When theprobe temperature reaches or exceeds 50 (35+15), the controller outputs the full pace sign and the fan runs at complete velocity According to the explicit functionality of the fan, the particular pace of the fan could be considerably various 6 method: P The controller has supported the management of the reverse timing fan, energy off and remove the fan Press the set button to affect the controller Keep the settings button continually maintain (about three seconds) until the three lighting fixtures turn into double flash state after which release the button The indicator lamp turns into a single light, which represents the entry mode environment state The controller is split into 3 sorts of operating modes, reminiscent of 1, 2, three indicator gentle double flashing, through short press button switch, set the long, press the button to save lots of and exit the set mode and automatically again to ordinary operating state The 3 operating modes are as follows: 1> conventional PWM fan management mode (default mode) This mode is used for the 4 wirefan management of the traditional Intel specification 2> traditional opposite series PWM fan management mode This mode is used in maximum opposite timing four cord fan control When the fan is in common mode control, the speed change is opposite, and the management line is attached to the destructive pole at full velocity 3> reverse collection fan 80% management mode This mode is used in a very rare sort of opposite timing fan When the fan is in traditional mode control, the rate change is opposite, and the management line is not became when the detrimental electrode is hooked up